Gunsmith Price ListPrices subject to change without notice.
|
Download a copy |
| SINGLE SHOT BARREL WORK | |
| BARREL SINGLE SHOT RIFLE Thread, chamber, cut & crown, cut 2 dovetails, fit extractor (same case head size) stamp with caliber and rate of twist. (Does not include: drilling and tapping of any holes, nor polishing or bluing) |
$350 |
| MODIFY EXTACTOR TO A DIFFERENT CASE HEAD SIZE | $50 |
| DOVETAILS EACH Front or rear sights (specify size), Barrel Lugs for mounting of Forearm or Lever or Main Spring. |
$35 |
| DRILL & TAP HOLES EACH Forearm mount, Scope blocks, Tang sights |
$20 |
| BARREL FINISHING |
|
| Octagon - draw file and hand polish to 320 grit with hot blue | $225 |
| Octagon � draw file and glass bead with hot blue | $175 |
| Round � draw polished to 320 grit with hot blue | $175 |
| Round � spin polish to 400 grit and glass bead with hot blue | $125 |
| RECROWN BARREL | $50 |
| SHORTEN & RECROWN BARREL | $65 |
| RE-CHAMBER BARREL | MINIMUM $85 |
| INSTALL LINER AND CHAMBER THE BARREL (Does not include cost of Liner) |
$200 |
| SINGLE SHOT ACTION WORK | |
| BUSH BREECH BLOCK TO REDUCE FIRING PIN DIAMETER OR RESTORE GAS CUT DAMAGE IN BREECH BLOCK FACE | $75 |
| SQUARE FACE OF RECEIVER TO THE ACTION THREADS & TRUE BREECH BLOCK TO THE FACE OF THE RECEIVER | MINIMUM $125 |
| TIG OR MICRO WELDING RESTORATION P.O.R. HAND POLISHING | $35/HR |
| STOCK WORK ON 2-PIECE STOCKS | |
| INSTALL SEMI-INLET STOCK TO YOUR ACTION BUTT STOCK & FOREARM, GLASS BED, 3 COATS OF OIL FINISH, INSTALL RECOIL PAD (DOES NOT INCLUDE THE COST OF STOCK BLANKS OR RECOIL PAD) |
$650 |
| RAISED PANELS RAISED HALF ROUND OR ELIPTICLE PANELS IN FRONT OF & BEHIND THE ACTION, BLENDING TO THE SIDES OF THE RECEIVER |
$250 |
| DELUXE FINISH TOTALLY FILLED GRAIN WITH HAND RUBBED OIL FINISH |
$200 |
| INSTALL STEEL NOSE CAP ON FOREARM INCLUDES POLISHING, INLETTING AND THREADING FOR MOUNTING SCREW |
$125 |
| STEEL BUTT PLATE INSTALLED A CRESCENT, SHOT GUN, OR SCHUETZEN BUTT PLATE INCLUDES FINISHING OF THE CAST BUTT PLATE & HOT BLUING, INSTALLING AT REQUESTED LENGTH OF PULL, & GLASS BEDDING TO BUTT STOCK (DOES NOT INCLUDE PRICE OF PLATE OR COLOR CASE HARDENING OR PLATED FINISH) |
$125 - $225 |
| CHECKERING OF STOCKS (TYPICAL) | $225 - $350 |
| ROLLING BLOCK SPECIALTY WORK | |
| TRIGGER JOB (2-3 # PULL) | $90 |
| OCTAGON TOP RECEIVER (WHEN POSSIBLE) | $80 |
| THIN MILITARY ACTION TO SPORTER THICKNESS REQUIRES RE-COUNTER BORING OF SCREW HOLES & SHORTENING SCREWS & ACTION PINS |
$150 |
| RE-CONTOUR MILITARY BREECH BLOCK OR HAMMER SPUR TO SPORTER CONFIGURATION AND CHECKER SPUR | $75 |
| REMOVE MILITARY STOCK FLANGES FROM BOTH ENDS OF RECEIVER | $80 |
| RE-CONTOUR THE MILITARY TRIGGER GUARD TO SPORTER CONFIGURATION & POLISH TO 320 GRIT (DOES NOT INCLUDE WELDING SLING SWIVEL HOLES IN SOME GUARDS) |
$125 |
| CONVERT LOWER TANG TO PISTOL GRIP CONFIGURATION NARROW & TAPER BOTH TANGS TO SPORTER CONTOUR | $250 |
| TAPER TANGS & REDUCE WIDTH TO SPORTER CONFIGURATION TAPER AND EXTEND LOWER TANG TO ORIGINAL SPORTING CONFIGURATION INCLUDES ADDING THE WOOD SCREW TO THE REAR OF THE TANG. |
$200 |
| ACCURIZE ROLLING BLOCK ACTION INCLUDES THE FOLLOWING: TRUE THE FRONT OF THE RECEIVER TO THE ACTION THREADS, TRUE THE BREECH BLOCK TO THE RECEIVER FACE, PRECISION REAM THE ACTION, BREECH BLOCK, & HAMMER, MAKE AND INSTALL NEW ACTION PINS, REMOVING ALL PLAY & LATERAL MOVEMENT IN THE BREECH BLOCK & HAMMER (REQUIRES ANEALING OF THE ABOVE PARTS, PRICE DOES NOT INCLUDE RE-COLOR CASE HARDENING) |
$225 |
| THIS MODIFICATION IS THE BASIS FOR A TRUE TARGET-GRADE ROLLING BLOCK ACTION. | |
| DEPOSIT REQUIRED: 1/3 OF LABOR AND 100% COST OF PARTS AND OUTSIDE SERVICES. | |
| MY SPECIALTY IS RESTORATION AND UPGRADING OF SINGLE SHOT RIFLES, BUT AS THE NAME OF THE COMPANY IMPLIES I SPECIALIZE IN ANY CUSTOM WORK. IF YOU HAVE SOMETHING SPECIAL IN MIND OR A PROJECT THAT IS A LITTLE OUT OF THE ORDINARY, FEEL FREE TO CONTACT ME WITH YOUR IDEAS | |
| ** HIGH QUALITY WORK DONE WITH PRIDE ** | |
| CURT HARDCASTLE - 575-574-8825 - 3839 W. TOM LYONS DR - SILVER CITY, NM - 88061 | |